I’m in the process of evaluating a really awesome little machine called the EBox 4863.They are small, have no fans or moving parts (apart from when you put a laptop hard disk in), and will likely suit both urban and remote implementations as well as humid Pacific conditions.
I’m still testing so I don’t have a final verdict (will post soon) but so far I really love these little boxes 🙂 They do seem a little warm, but they are designed to be basically just one big heat sink 🙂 If you get one, make sure you get the 4863S as it comes without an OS (and in Australia, the only OS you can get is Windows).
Specifications
- VIA Esther 1.2GHz
- 1GB DDR2
- MPEG4/WMV9 decoding accelerator
- Dual LAN
- Compact Flash slot
- Mini PCI socket
- 2 x USB 2.0 ports
- Support 2.5″ HDD
- PXE diskless boot
- Wireless LAN (option)
Cost
Approximately $550-$600 (AUD).
Installing the hard disk
Requirements: small Phillips screwdriver, IDE laptop hard disk (3 1/2 inch). Some time 🙂
Firstly you need to use the Allen key that comes with the box to open the bottom of the EBox, that is the side that doesn’t have the VGA and power. Then undo the two screws on the back (where the devices plug in) and loosen the back cover so it doesn’t inhibit the top motherboard being removed.
Once open you need to undo the four screws in the top section of the motherboard and you need to lift the top board straight up as below. Note that there are two sets of pins, one on each side underneath the top board, so you need to lift straight up to get it off:
Remove the top board
Turn the top board over and you’ll see the pins. Take the very short IDE cable. Join the IDE cable to the top board, and to your IDE hard disk. Then you’ll have to align the HDD with the holes in the board which ends up squishing the HDD up close to where the IDE cable plugs in.
Now carefully put the board back in place ensuring you line up the pins correctly on the underside of the board. Then screw the backplate on like below.
Final step – replace the cover and ensure you put the correct screws into the correct side. The side without the board gets the long screws 🙂
And there you have it, below is a picture of the EBox with a great little 9.2″ monitor alongside my rather large looking IBM T42 laptop and an XO. Welcome to my workbench today 🙂
Installing the XS software
Requirements: Internet access, USB key (at least 700MB)
Firstly,you need to make it bootable from the USB key. Delete will get you into the BIOS, and you have to have to USB plugged in when you turn it on to choose USB as a boot option and to move it to the top of the boot options.
Then you have to make the bootable USB key with the XO image. At this stage I’m still on XS 0.4 for deployments and testing 0.5, but the process is generic. You can following the directions for 0.4 here, or the most recent image here.
I’ve tested XO 0.4 and am testing 0.5. All looks pretty good! Only problem so far is that on 0.5 the graphic card didn’t seem to show the Fedora boot screen, so I just pressed enter to a blank screen which worked fine (as I knew the question would be whether to install).
Update: 0.5 doesn’t appear to work on it, and neither does Ubuntu Hardy. Am trying to come up with work arounds. Input welcome! Error on XS 0.5 (Fedora 9) installation is GrubbyPartitionName. It finishes copying the packages and then fails.
Update II: To make 0.5 work I had to a) ensure it was referencing the correct location for the ks.cfg file, and b) comment out/delete an option in the ks.cfg which for some reason causes it to crash. I’ve updated the 0.5 install page and now have successfully installed 0.5 on the eebox! Yay!